Os fusos de esferas são os componentes de transmissão mais usados em máquinas-ferramentas e máquinas de precisão. Sua principal função é converter movimento rotacional em movimento linear, ou converter torque em força repetitiva axial. Ao mesmo tempo, também possui características de alta precisão, reversibilidade e alta eficiência.
Excentricidade: Refere-se ao desvio central entre o lado fixo e o lado de apoio.
Inclination: In addition to eccentricity, the installation error caused by the parallel error (up, down, left, and right) or vertical error of the screw nut mounting part between the screw shaft and the guide (LM guide, etc.).
Installation accuracy reference: Refer to the table for the reference value of the installation accuracy of the ball screw. The data in the table is for reference only. Please minimize installation errors. The installation accuracy of the motor support and coupling affects the walking and positioning accuracy of the workbench, so attention should be paid to the ball screw.
Unpacking: Be careful not to hit the nut and end thread. When disassembling the nut, you can manually rotate the nut from one end of the effective thread to the other end. Check whether the resistance is consistent and whether there is obvious bending. Be careful not to disengage the nut screw from the effective thread. Wipe off the surface anti-rust oil and apply lubricating oil.
Maintenance: When the linear speed is less than or equal to 30m/min, grease can be used for lubrication. According to the working conditions, grease should be injected every 300 to 600 working hours. It is recommended that oil lubrication be 30-60m/min, e lubrificação forçada por névoa de óleo pode ser considerada 60-100m/min. Recomenda-se encomendar um parafuso oco e adotar refrigeração e lubrificação forçadas. Mantenha o ambiente de trabalho limpo e não deixe que poeira e outras impurezas entrem na pista ou na porca. Se a situação não for boa, considere adicionar uma capa protetora aos parafusos.
Ball screws are usually used where precise positioning is required. The ball screw has high mechanical efficiency, low transmission torque and almost zero axial clearance, making it an important device in tool positioning and aileron drive applications. However, the resistance and heat generated by continuous operation may cause large friction and positioning errors. Increasing the design coefficient of the ball screw friction will also increase the torque, which in turn affects the positioning accuracy. When the ball is pressed between the ball screw nut and the screw shaft, the wedge effect is a potential source of friction. When rotating in the forward direction, the ball is usually pressed on the nut; on the contrary, the ball is squeezed on the screw shaft. Since the sliding friction coefficient is much larger than the rolling friction coefficient ({{0}}.1-0.3 when there is no movement, 0.001-0.003 when rolling), the wedge effect greatly increases the torque.
Ball screw drive has the following advantages:
①Alta eficiência de transmissão. A eficiência de transmissão da transmissão do fuso de esferas é geralmente 20,92-10 por cento, e a eficiência de transmissão da transmissão de parafuso deslizante comum é 20,20-0.40.
②Alta precisão de transmissão, movimento estável e nenhum fenômeno de rastreamento. O acionamento do fuso de esferas é basicamente atrito de rolamento, com pequena resistência ao atrito, e a resistência ao atrito não tem quase nada a ver com a velocidade do movimento.
③Funcionamento em marcha-atrás sem ralenti. Após o pré-aperto do fuso esférico e da porca, a folga axial pode ser eliminada. Desta forma, não há zona morta na direção oposta e a precisão e rigidez da transmissão axial são melhoradas.
④É reversível. Como a perda por atrito do fuso de esferas é pequena, ele pode ser convertido de um movimento rotativo para um movimento linear e também pode ser convertido de um movimento linear para um movimento rotativo. Tanto o parafuso de avanço quanto a porca podem ser usados como acionamento ou seguidor.
⑤Longa vida útil. Devido à pequena perda de atrito do atrito de rolamento, a vida útil é longa.
As a precise and labor-saving transmission mechanism, the ball screw is widely used in precision machine tools and CNC machine tools due to the above advantages.
Why not give us a linear challenge?
Contate agora
E-mail: sales@gyballscrew.com Tel(Whatsapp): mais 86 17769816967
seller@gyballscrew.com plus 86 17769815516
saleChen@gyballscrew.com plus 86 15325179771
